Weston 650201.0 Manuel d'utilisation et d'entretien télécharger pdf (Page 7)

-7--10-

POWER SUPPLY

Insert the connector end of the Power Cord into the

Power Cord Port on the right side of the unit. Insert

the Plug on the Power Cord into a standard 120-volt

grounded electrical outlet

Figure 2. DO NOT modify the

plug to t an unsuitable outlet.

Power

Indicator

Switch

Power Cord

Port

Connector

End

Plug End

GROUNDING

This appliance must be grounded while in use to protect

the operator from electrical shock. The appliance

is equipped with a 3-conductor cord and a 3-prong

grounding type plug to t the proper grounding-type

receptacle. The appliance has a plug that looks like

Figure A. An adaptor, Figure B, should be used for

connecting Figure A plugs to two-prong receptacles.

The grounding tab which extends from the adaptor

must be connected to a permanent ground such as

a properly grounded outlet box as shown in Figure C

using a metal screw.

EXTENSION CORDS

Use only 3-wire extension cords which have 3-prong

grounding-type plugs and a 3-pole cord connector

that accepts the plug from the appliance. Use only

extension cords having an electrical rating not less

than the rating of the appliance. Do not use damaged

extension cords. Examine extension cord before using

and replace if damaged. Do not abuse extension cord

and do not yank on any cord to disconnect. Keep

cord away from heat and sharp edges.

Figure A

Figure B

Figure C

Circuit

Grounding

Conductor

Grounding

Prong

Metal

Grounding

Screw

Cover of

Grounded

Outlet Box

Grounding

Means

AA2220

GROUNDING INSTRUCTIONS

Power

Cord

Figure 2

PREPARING VAC BAGS FROM A ROLL

1. Make sure the Vacuum Sealer is in the “OFF” position. Attach the Vacuum Sealer

to the power supply.

2. Turn the Vacuum Sealer “ON”.

3. The “POWER” Light on the display, “POWER INDICATOR” Switch both will

illuminate and the Internal Cooling Fan will run.

4. Open the Vacuum Lid.

5. Cut a vacuum bag to the length you want from a roll.

6. Place either open end of the bag against the outer face of the Oval Vacuum

Chamber Seal in the Vacuum Chamber (not in the Vacuum Chamber).

7. Close the Vacuum Lid. The bag end should be sandwiched between the Vacuum

Lid Seal and Seal Bar Heating Element. Make sure there are no wrinkles or creases

in the bag in the sealing area.

8. Press and hold the Vacuum Lid Handle down. You may need to continue holding

the bag.

9. Press the “START” Button (this will engage the Pump and the Heating Element).

Press the Manual Seal Button to seal the vacuum bag.

10. Sealing is complete when the Vacuum Chamber releases after a 3 second cooling

period (the “COOL” Light will illuminate). The release is audible.

11. Open the Vacuum Lid and remove the bag. DO NOT try to open the Vacuum Lid

before the vacuum has released or unit damage may occur. Wait at least 20 seconds

before sealing another bag to avoid overheating the unit.

12. Turn the Vacuum Sealer “OFF” and unplug the Power Cord when you are done.

Some parts of the Vacuum Sealer may need replacing after repeated use. A Vacuum

Sealer Maintenance Kit

(Sold Separately Model No. 08-0501-W) may be necessary for the

Vacuum Sealer to properly function.

REPLACING THE OVAL VACUUM CHAMBER SEALS:

1. Turn “OFF” the Vacuum Sealer and remove the Power Cord from the electrical

outlet.

2. Make sure the unit is completely cool.

3. Open the Vacuum Lid.

4. Remove the Oval Vacuum Chamber Seal from the groove on the underside of

the Vacuum Lid.

5. Remove the Oval Vacuum Chamber Seal from the groove in the Plastic Vacuum

Chamber.

SERVICE INSTRUCTIONS

WARNING! Before cleaning, assembling or disassembling the Vacuum

Sealer, make sure the Vacuum Sealer is OFF and the PLUG IS REMOVED

FROM THE OUTLET/POWER SOURCE!

1 2 3 4 5 6 7 8

Commentaires sur ces manuels

Pas de commentaire

Weston 650201.0 Manuel d'utilisation et d'entretien Page 7

Commentaires sur ces manuels