Weston Pro 3000 Vacuum Sealer Manuel d'utilisateur télécharger pdf (Page 9)

1. ALWAYS allow the sealing bar to cool for approximately 20 seconds between bags.

Leave the Clear Acrylic Vacuum Lid OPEN between uses, this allows the Heating

Element to cool more quickly between bags.

2. Unroll the appropriate amount of bag material for the item that you wish to seal. The

bag should be at least 2” (5 cm) longer than the item you are sealing.

3. Place one end of the bag onto the Sealing Bar, leaving about 2” (5 cm) of the empty

part of the bag beyond the inside edge of the Sealing Bar.

4. Be sure not to cover the Vacuum Port with the bag. Covering the Port prevents the

proper vacuuming of air from the bag.

5. Close the Clear Acrylic Vacuum Lid while holding the bag in place.

6. If the Power Light is not illuminated, press the Power Button to turn on power to

the Vacuum Sealer.

7. If the Manual Light is not illuminated, press the Mode Button until the Manual

Light is illuminated to select the Manual Mode.

8. Press the Start Button engaging the Vacuum Pump (the Vacuum Pump must be on

for the Seal Bar to heat up).

9. You may need to apply slight pressure to the Handle at the beginning of the

countdown process in order to create a proper seal.

10. Press the Manual Seal Button immediately after the 2-Piston Vacuum Pump

starts. (Press down on the Clear Acrylic Vacuum Lid to contact the Sealing Bar.)

11. After the Seal Window counts down to zero (0) the unit will automatically release

the vacuum and enable the Clear Acrylic Vacuum Lid to open.

12. Remove the bag and inspect the seal. The seal should appear smooth and

consistent all the way across the bag. The seal SHOULD NOT melt through the bag at

any point. Be sure there are no creases or wrinkles that may allow air to leak into the

bag. A properly sealed bag will not pull apart.

13. Do not form side seals on the bags, the sides are already sealed.

14. If the seal is good, proceed with vacuum packaging. Otherwise:

If the seal is melted through the bag trim off the bad seal with scissors

and adjust the Seal Time Down (-) in one second increments and try the

test process again.

If the seal has not fully welded the bag closed, trim off the bad seal with

scissors and adjust the Seal Time Up (+) in one second increments and try

the test process again.

INITIAL TESTING OF THE BAG SEAL

Test seal a couple of vacuum bags to be sure that the Seal Time is set properly.

The Seal Time may need to be increased (+) or decreased (-) to optimally seal

a bag.

NOTE: The Vacuum Sealer is ONLY intended to be used with VACUUM BAGS. For

best results, only use the recommended vacuum bags with an embossed or mesh lining.

DO NOT USE HOUSEHOLD BAGS! Any other uses of the Vacuum Sealer, other

than the uses described in this booklet, could potentially damage the appliance and void

the warranty!

PREPARING VAC BAGS FROM A ROLL

1. Turn the Vacuum Sealer “ON”.

2. The “POWER” Light on the display, “POWER INDICATOR” Switch both will

illuminate and the Internal Cooling Fan will run. Make sure the unit is in Manual Mode.

3. Open the Vacuum Lid.

4. Cut a vacuum bag to the length you want from a roll.

5. Place either open end of the bag against the outer face of the Oval Vacuum

Chamber Seal in the Vacuum Chamber (not in the Vacuum Chamber).

6. Close the Vacuum Lid. Check that the bag opening is in the center of the Vacuum

Chamber.

7. Press and hold the Vacuum Lid Handle down. You may need to continue holding

the bag.

8. Press the “START” Button (this will engage the Pump and the Heating Element).

Press the Manual Seal Button to seal the vacuum bag.

9. Sealing is complete when the Vacuum Chamber releases after a 3 second cooling

period (the “COOL” Light will illuminate). The release is audible.

10. Open the Vacuum Lid and remove the bag. DO NOT try to open the Vacuum Lid

before the vacuum has released or unit damage may occur. Wait at least 20 seconds

before sealing another bag to avoid overheating the unit.

12. Turn the Vacuum Sealer “OFF” and unplug the Power Cord when you are done.

WARNING! Before cleaning, assembling or disassembling the

Vacuum Sealer, make sure the Vacuum Sealer is OFF and the PLUG IS

REMOVED FROM THE OUTLET/POWER SOURCE!

NOTE: The Vacuum Sealer is ONLY intended to be used with VACUUM BAGS. For

best results, only use the recommended vacuum bags with an embossed or mesh lining.

DO NOT USE HOUSEHOLD BAGS! Any other uses of the Vacuum Sealer, other

than the uses described in this booklet, could potentially damage the appliance and void

the warranty!

-9--12-

1 2 3 4 5 6 7 8 9 10

Commentaires sur ces manuels

Pas de commentaire

Weston Pro 3000 Vacuum Sealer Manuel d'utilisateur Page 9

Commentaires sur ces manuels

Produits connexes et manuels pour Cuisine Weston Pro 3000 Vacuum Sealer